The second way to do this involves a few more steps, but is safer since you do not change the source. Technique 2: Create Image, Restore to Disk Image, Shrink, Clone and Restore. The size shown next to the image in sources is the minimum size SD Card you will need to restore the image.
Making A Microsd Image For Beaglebone And Install A BeagleBoneThere may be issues with booting your BeagleBone from the image on the SD card.And other Internet networking options. The steps I take to install a BeagleBone Black are to take an sd card I had previously dd'd an image of wheezy into, then insert it into the BeagleBone Black, hold down a button while booting, and the image gets burned onto the BeagleBone Black's eMMC.Lets begin with turning on the BeagleBone and making sure it works. Unlike the previous SD card images, the Stretch image does not work out-of-the-box and requires a minor adjustment and this tutorial explains the necessary steps in detail.This page describes how to configure a static IP address on a Beaglebone Black and the configuration of nameserversI have made a basic build of the update-image.bb recipe which created a core-image-full-cmdline-beaglebone.wic file ready to be transferred to the SD card.BeagleBone Black: Getting an image from eMMC back to the SD Card. This tutorial shows how to setup your BeagleBone Black board to run the Debian Stretch distro. Clear Wiring Diagram: Setup Connecting the Beaglebone Black to the InternetRunning Debian Stretch images on BeagleBone. Thorough and mindful research is crucial to making sure you get your.Test the InternetConnection by using your Beaglebone Black connected USB keyboard/mouse and monitorTo start up a shell prompt on the LXDE Window. However, as discussed below, you really do need to be connected to the Internet - at least initially.You are going to need an Internet connection for the next step when you upgrade all of the software you just installed and to obtain other packages.The ethernet cable should be plugged into the Beaglebone Black's RJ45 ethernet port and the other end into an Internet connected LAN port. If you are not going to connect the Beaglebone Black to the Internet you can comment out the line iface eth0 inet dhcp inThe /etc/network/interfaces file to speed things up. The discussion below assumes the presence of that hardware setupIt should be noted that the current page is a revised edition of a previous page and it now focuses on theBeaglebone Black specific Debian 9.5 4GB SD LXQT Debian distributionAvailable for download from the Beagleboard.org website.After you boot off the MicroSD card as described on the previous page, you may find that it takes a whileFor the Beaglebone Black to start the LXDE GUI (it might look like it is hung).It isn't actually hung, the delay of a minute or so is because the new installation is looking for a DHCP server to give it an IP addressAnd if it cannot find one it will take a while toTime out. This page is a pre-requisite for a following pageAnd the contents of this page are oriented towards that end result.Previous pages in this series describe the installation procedure for the Debian ArmhfOperating system on a MicroSD card and a suitable hardware setup.Also, later on,You will want the IP address to remain unchanged (static) for when you configure networking to the Beaglebone Black as part of the remote compilationTo set up nameservers. This will make it awkward toSsh into the Beaglebone Black from the remote development PC because you will have to figure out which IP address it is using each time. This is good in the sense that an InternetConnection will probably be immediately operational, however, it is bad because it means the IP address can change each time you boot. If that does not work you'll need to debug the Internet connectivity before proceeding to the install of Mono and C#.Use the command ip addr show to see your IP address and attempt to ping that address from the Beaglebone Black and also fromA remote PC and take all the other standard actions to debug this sort of thing.As mentioned above, by default, when the Beaglebone Black first starts, it will try to get its IP address via DHCP. It may just be that you do not have a DHCP server on your network and hence have no automatically assigned IP address.In that case, the static ethernet configuration discussion below will get you going. If you do notGet a response then your Internet connection is not working.Comment out the line below which automatically.and add the lines below which force it to be a static IP address. You can ask the network administrator for this or, if it is your personal local area network, find out the IP addresses ofOther devices on the same network and attempt to figure out an unused address using them.Use the command (as root) nano /etc/network/interfaces to edit the interface definitions (make a copy of this file first). If you don't have a DHCP server which assigned the IP address you'll needTo find out a suitable unused IP address. We might as well use that one for the staticAddress since we are now pretty sure that it is not in use by anything else on the network. Issue the command ip addr show | grep eth0Inet 192.168.1.102/24 brd 192.168.1.255 scope global eth0The value 192.168.1.102 is the assigned IP address given to the Beaglebone Black by the network DHCP server. Note that I also disabled the entire iface usb0Section because I did not want to be able to connect to a PC via the USB Ethernet/RNDIS gadget.# This file describes the network interfaces available on your system# and how to activate them. The gateway IP address ( 192.168.1.254) inThis example is the IP address of my side of the ISP'sInternet hub - your gateway IP address will probably be different.Once the edits are completed, my /etc/network/interfaces file looked like the one below. You can certainly substitute other ones if you wish. The ones used in theExample below are the Google public nameservers. Search for email in outlook 2016 on macPuTTY is free and can be found on the website belowI'll not tell you how to install and configure PuTTY here – you can easily find out a lot of information on how to do that on the Internet. Windows platforms do not have a "built in" ssh client so you'll you have to install an application that provides it.There are many such software programs – the most common of which isPuTTY. If any of these thingsAre not working correctly, you really should correct them before moving on to the next steps.Digression: Connecting using SSH Telnet ClientTelnet is basically a method of presenting a shell prompt from a remote device in a window on a local computer (in this case a Windows PC).Telnet itself is not used much anymore as it is pretty insecure and is disabled by default on nearly all new Linux installations.A similar mechanism called SSH ( Secure SHell) is used in its place.In order to use SSH to connect to the Beaglebone Black from a remote Linux machine you would simply start a shell prompt on that remote machine and enter a commandLike ssh 192.168.1.102 -l debian. In addition you should find thatThe date command will show that the system dateIs now set correctly since the startup routines that try to set that can now find a date and time server on the Internet. You should also find that you canSuccessfully ping 192.168.1.102, ping 8.8.8.8 and also ping google.com.Also check that you can ssh (see below) into the Beaglebone Black from a remote PC using that IP address. Or on host side, usbnet and random hwaddr# Note on some boards, usb0 is automaticly setup with an init scriptReboot the Beaglebone Black by issuing the command reboot or by cycling the power and you should find, once it restarts, that theIP address is statically set to the value of 192.168.1.102 or whatever you entered. Virtually no modern Linux installations will permit this.
0 Comments
Leave a Reply. |
AuthorShannon ArchivesCategories |